If you possess an Asus router you have undoubtedly noticed that it has many indicator lights each of which indicates a distinct state. When a specific light suddenly emerges it might cause concerns. It’s the blinking blue light. Go through this blog to find causes of the Asus router blinking blue light and offer workable solutions.
What Does the Blinking Blue Light on an Asus Router Mean?
When an asus router blinking blue light it usually means that pairing mode is enabled or that the router is trying to connect to the internet. Usually happening during setup or during a reset this might also indicate problems with your network connection.
The following are the most typical causes of asus blinking blue light:
- Router Initialization: This refers to the router’s initial boot up or internet connection phase.
- WPS Pairing Mode: During the pairing process the blue light on the router will flash if it is attempting to connect a device using WPS (Wifi Protected Setup).
- Firmware Update: A new firmware version may be downloaded or being installed on your router.
- Problems with the Internet Connection: The router is having trouble establishing or keeping up a reliable internet connection.
Let’s go over each possible situation and how to handle it.
How to Fix asus router Blinking Blue Light
1. Hold off till initialization is finished.
The asus blinking blue light can just indicate that it’s merely booting up after you turned it on or restarted it. For the device to finish booting up and establish a reliable connection with your internet service provider (ISP) it usually takes a few minutes.
How to proceed:
- Give it at least two to three minutes.
- If it doesn’t work check another troubleshooting advice.
2. Verify Internet access
One of the most common signs that your router is having distress linking to the internet is a flickering blue light. This may occur as a result of configuration errors, bad wires or problems with your ISP.
How to proceed:
- Check the strength of your internet connection:
- Confirm that all the wires are suitably attached.
- Turn your modem back on
- After 30 seconds of not using your modem connect it back in.
- Restart the router
- After your modem has returned to service, disconnect your Asus router, wait ten to fifteen seconds and then plug it back in.
- In order to find out whether there is an outage or problem on your ISP’s end, get in touch with them if the internet connection is still not established.
3. Pairing Mode for WPS
The blue light on your router will flicker while it tries to establish a secure connection with the device if you’re connecting it to your network using WPS.
How to proceed:
- A few minutes may pass before the pairing procedure is finished.
- If the asus router blinking blue light persists despite an unsuccessful WPS connection attempt, consider disabling the pairing and manually reconnecting using your device’s Wifi settings.
4. Firmware Update Ahead
Firmware upgrades are sometimes applied to Asus routers in order to enhance functionality security or performance. The asus router blinking blue light to let you know that the update is downloading or installing throughout this procedure.
How to proceed:
- When the router is updating its firmware don’t interfere with it. Give it time to finish the process—it may need several minutes.
- Try logging into the router’s admin panel to see if the firmware upgrade was successful if the asus blinking blue light continues after ten minutes.
To examine or upgrade the firmware manually:
- Enter IP address in browser to access Asus router web interface.
- Enter your admin credentials to log in.
- To check for updates navigate to Administration > Firmware Upgrade.
- Fix any apprises that are accessible
5. Router Factory Reset
You might need to factory reset if asus router blinking blue light doesn’t go away after trying all of the aforementioned fixes. By doing this you may return the router to its original configuration and get rid of any mistakes or customized setups that might be the source of your connectivity problems.
How to proceed:
- On the rear of your router look for the Reset knob.
- Press and hold the Reset knob until the power light starts to blink using a paperclip or other such item.
- Let the router reboot by releasing the knob.
- Reconfigure your router by following Asus router setup instructions.
- Remember that you will need to re enter your network settings including your Wifi name password and any other custom settings following a factory reset.
6. Speak with us
If after following all the above instructions your Asus router is still glowing blue there can be a hardware problem or an advanced asus router setup issue that has to be looked after by an expert. In such a situation speak with our team for more advice. Prepare to provide the specifics of the problem along with the model number of your router.
Final thoughts
Although an Asus router blinking blue light doesn’t always indicate a problem it’s still important to know what it signifies and how to fix it. Most problems can be fixed with a few easy steps whether it’s the router not starting up, not connecting to the internet or a firmware update. The techniques listed above will help you restore your router’s functionality.